Provide solutionsfor the upgrade of steel structure CNC Fiber Laser/Plasma cutting and welding machine

Home / All / cutting machine / What tolerance and edge quality can a CNC plasma cutting table really hold?

What tolerance and edge quality can a CNC plasma cutting table really hold?

Update Time:2026/11/17

Table CNC plasma cutting machine for metal sheet

What tolerance can a 1500x3000 CNC plasma cutting table actually hold?

Expect two different numbers, and be suspicious of anyone who quotes only one. Positional tolerance - where the profile lands on the sheet - is about plus or minus 0.5 mm on 1-6 mm sheet and opens to plus or minus 1.0 mm, sometimes 1.2 mm, on 12-25 mm plate; the YMT-1530 is specified at less than or equal to plus or minus 1.0 mm auto precision across its full 1500 x 3000 mm working area, which is realistic for a machine with square linear guides, a double-driven rack and pinion and the Fangling F2100B control. Cut-face quality is a separate specification: on a conventional air plasma source the angularity in ISO 9013 terms typically lands in range 4-5, on a high-definition class source around range 3, and range 2 on material under 10 mm with a well-tuned table and dry air. Kerf is 1.5-3 mm depending on amperage, against 0.15-0.35 mm for fiber laser, and that difference alone changes how you nest and how you compensate. The honest summary: a plasma table is a shape-making machine that holds plus or minus 0.5-1.0 mm, not a fitting machine. It is the right tool when the drawing controls a profile that will be welded, bolted with clearance or ground afterwards.

Why is one side of every plasma cut beveled, and how do I reduce it?

Because the arc is a cone, not a cylinder: it is narrowest at the nozzle and widens as it travels through the plate, so the exit side of the kerf is always wider than the entry. On 6-10 mm steel the bevel is typically 2-3 degrees per side, it drops to about 1 degree on 12-38 mm and under 1 degree on 50 mm, and the more vertical side is consistently the right-hand side of the kerf relative to travel direction. You cannot eliminate it on a conventional table, but you can control it: hold a constant standoff with arc-voltage THC (the F1621 tracks arc voltage and keeps the torch at the height the cut was tuned for), keep the nozzle orifice round and the shield cap clean, match amperage and speed to thickness, and pierce at the correct height before dropping to cut height. Two practical tricks matter more than most operators expect - put the critical feature on the vertical side of the kerf by orienting or mirroring the part in nesting, and cut the outside of a tolerance-critical contour in the direction that leaves the good face on the part rather than on the scrap.

What is the smallest hole a plasma table can cut, and when should I drill instead?

The working rule is hole diameter at least equal to material thickness, and 1.5 times thickness if you want a round hole rather than a slightly keyholed one. Below that ratio the arc never completes a full circle before heat input distorts the geometry, and the hole comes out oval, tapered and offset. There is a second limit: a hole needs enough circumference for the arc to stabilize, so a 3 mm hole in 3 mm plate is worse than the ratio suggests. For bolt holes, the reliable approach on a plasma table is to cut undersize and finish to size - typically cut 1.5-2 mm under nominal, then drill or ream - because plasma holes carry 0.3-0.5 mm of taper and a recast edge that a bolt does not like. For M12 and up in plate up to 10 mm, cut-and-ream works well and is far faster than drilling from solid. For slip-critical connections, EN 1090 or AISC-bearing-type joints, and anything with a positional tolerance tighter than plus or minus 0.5 mm, drill or use a high-definition source with hole-specific process technology.

Does the plasma heat-affected zone damage the part or affect welding and painting?

On plain carbon steel the HAZ is narrow - roughly 0.2-0.8 mm on thin and medium plate against 0.1-0.25 mm for fiber laser - and it is not a structural problem for welded fabrication: the zone is fully consumed by the weld or sits in the heat-affected region the weld creates anyway. The problem cases are specific. Stainless and aluminum cut with air or oxygen get a chromium-depleted, oxidized or nitrided skin that kills corrosion resistance, so remove 0.2-0.5 mm mechanically before welding or passivation. Galvanized material needs the zinc ground back 10-20 mm from the weld line regardless of how it was cut. For coating, a plasma edge is rough at Ra 12-25 microns with a recast layer, so coating adhesion at the edge is the weak point: blast or abrade the edge as part of the ISO 12944 preparation, or accept that the edge will be the first place the paint fails. For hot-dip galvanizing the cut edge is fine, but the roughness holds more pickling acid, so rinse and dry cycles matter.

What parts should not be cut on a plasma table?

Bevel preparation is the first one: a K, V, X or Y weld prep needs a bevel head or a machining operation, not a vertical plasma kerf, and trying to fake it with a chamfered cut leaves an inconsistent root face. Tube and pipe are the second: without a rotary axis and a proper pipe CAM package, a cutting table cannot produce a saddle or a mitered intersection. Third, precision features - bores, bearing seats, sealing faces, keyways - because the drawing controls a fit, and plasma holds a shape. Fourth, production work above roughly 25 mm where oxy-fuel is cheaper per metre and produces a squarer edge; the YMT-1530 accepts an optional flame torch for 6-150 mm mild steel exactly for this reason. Fifth, hardened or precipitation-hardening alloys where the recast layer can be harder than the base metal and will fight a carbide cutter. Everything else - brackets, base plates, gussets, gusset stiffeners, frames, guards, HVAC transitions, weldment blanks - is fair game, because those parts get welded or ground and the bevel and roughness stop mattering once the arc strikes.

How do I prove the table holds tolerance across the whole sheet?

Cut a test plate that uses the whole envelope, not a small square in the middle. A practical first-article set is a 300 x 300 mm square in each corner and one in the centre, a 200 mm circle, and a long straight strip cut along both diagonals - that single nest checks squareness, axis calibration, rack backlash and thermal drift in one run. Measure the squares with calibrated calipers and check the diagonals of each square within plus or minus 0.2 mm; compare every outside dimension against the programmed value to confirm kerf compensation is right; measure the circle at four points for ovality. Then do a fine-detail test: a row of holes at decreasing diameter and a part with a 5 mm internal radius, which shows where the process, not the machine, runs out. Repeat the whole test after any crash, after a rail or pinion service, and on a quarterly schedule - and record consumable hours at the time of the test, because a set of nozzles that is 80% through its life will fail a tolerance test that the machine itself would pass on fresh consumables.

Do kerf compensation and arc-voltage THC really change part size?

Yes, they are the two settings that quietly decide whether parts fit. Kerf on a 120 A air plasma source runs about 1.5-3 mm on 6-12 mm carbon steel and changes with amperage, speed, torch height and nozzle wear, so the offset stored in the CAM or the control has to match the consumable set actually installed - a machine left on an old kerf value produces parts that are consistently 0.5-1.5 mm off, and the error flips sign between outside profiles and internal holes if the compensation direction is wrong. Arc-voltage THC matters for a different reason: it holds a constant standoff on plate that is not flat, and plate is never flat. A 1 mm standoff error moves part size by roughly 0.2-0.4 mm and also changes the bevel angle, so without working THC you get good parts in the middle of the sheet and out-of-tolerance parts at the edges where the plate is dished. Add lead-in and lead-out geometry and corner slowdown to the list: they control hole roundness and the witness mark at the start point, which is where most customer complaints about 'plasma quality' actually come from.

When should a job move off the plasma table to laser, machining or a service center?

Use the table where the part is flat, two-dimensional, carbon steel from roughly 1 to 20 mm, and the edge gets welded, ground or covered - that is where plasma wins on cost per cut, setup time and tolerance-to-price ratio. Move to fiber laser when the tolerance is tighter than plus or minus 0.2 mm, when the material is thin and the volume is high, when holes are smaller than material thickness, or when the edge must be paint-ready or weld-ready without grinding. Move to machining when the feature is a bore, a thread, a bearing seat or a sealing face, because no thermal process holds those. Send the job to a service center when the plate is above 25 mm at low volume, when it is a one-off that would take longer to nest and fixture than to buy, or when the material is exotic. The per-part arithmetic is simple: table time plus consumables plus edge finishing versus laser time plus gas plus no finishing. Most shops find the crossing point sits around 3 mm on thin work and around 20 mm on thick work, and the parts in between belong on the table.

Technical Specifications of Table CNC plasma cutting machine for metal sheet

ParameterValue
Share
CategoriesPlate Cutting Machine
BrandYOMI CNC Cutting&Welding Machinery
Product SpecificationsYMT-1530
Effective working size1500mm*3000mm
Control systemShanghai Fangling F2100B
THCFangling F1621
Motor and driverChuangwei and Leadshine
SoftwareStarcam nesting
Horizontal span1750mm
Effective cutting width1500mm
Longitudinal span3600mm
Effective cutting length3030mm
Plasma cutting power sourceHuayuan LGK120A
Effective cutting range1500*3000mm or customized size
Cutting methods1 plasma torch (Flame torch for option)
Plasma power sourceYomi (63A,100A,120A,160A,200A,300A,400A )/Hypertherm /Huayuan power source for option
Safety SensorAnti-collision protection system
TransmissionSquare Linear guide and gear rack
THC systemFangling F1621 THC
Auto-precision≤±1.0mm
Motor and driverStepper motor(Servo motor optional)
Cutting thickness6-150mm MS(by flame),by plasma according to the plasma power source
Control systemFangling 2100B
SoftwareSarcam(Fastcam optional)
Working Voltage/Frequency1-Phase 220V/ 3-Phase 380V±10%/50HZ

Product Gallery

Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail
Table CNC plasma cutting machine for metal sheet detail

Applications

The Table CNC plasma cutting machine for metal sheet is widely applied in steel structure prefabricated buildings, bridge and infrastructure construction, shipbuilding and marine engineering, heavy machinery manufacturing, power plant and industrial facilities, and offshore wind power structures.

Learn more about the Table CNC plasma cutting machine for metal sheet:
https://www.steelstructurer.com/pid18376201/Table-CNC-plasma-cutting-machine-for-metal-sheet.htm

For more information about Table CNC plasma cutting machine for metal sheet and other steel structure intelligent equipment, contact YOMI CNC Cutting & Welding Machinery. Our team of experts is ready to help you find the best solution for your manufacturing needs.

Contact Person
YOMI WhatsAPP
Full Name:
YOMI WhatsAPP
Tel:

+86 19053498672

Email:
sales@yomi-china.com
WhatsApp:
8619053498672
Address:
Factory Adress: 9 Changjie Road, Ningjin,Dezhou, P.R.China