Which assist gas should you run on an H beam laser cutter: oxygen, nitrogen or air?
Which assist gas should you run on an H beam laser cutter: oxygen, nitrogen or compressed air?
The gas choice follows the part, not the machine. On the YM-XHJG-1250, which handles flange widths of 100-600 mm, section heights of 100-1250 mm and carbon steel from 1 to 30 mm with a 20 kW fiber source, three gases cover almost every structural job, and the deciding question is what happens to the cut edge afterwards. Oxygen (99.5% purity or better, regulated to roughly 0.05-0.10 MPa at the nozzle) reacts with the hot iron and releases extra heat, so it cuts carbon steel 30-50% faster than an inert gas and needs less laser power for the same thickness; the trade-off is a blue-grey oxide layer on the cut face. Nitrogen (99.99-99.999%, 15-25 bar) is inert, so it produces a bright, oxide-free edge that can go almost straight into welding or painting, but it is slower on sections above roughly 10-12 mm and is the most expensive gas per hour. Compressed air is a blend of about 78% nitrogen and 21% oxygen and is the cheapest option, but it is really a thin-material tool: above about 6-8 mm on carbon steel you start to see dross, a duller edge and lost squareness. For structural fabrication the working split is oxygen for webs, flanges and stiffeners that will be welded or painted after normal edge prep, nitrogen for exposed architectural members, stainless or galvanized parts, and air only for thin brackets, jigs and non-critical parts.
How much does each assist gas actually cost per hour on a 20 kW H beam laser?
Build the number in two parts: electricity plus gas. A 20 kW fiber source at 70% duty draws roughly 60-70 kWh, so power alone is around USD 7-12 per hour at industrial tariffs, and that cost is the same whichever gas you choose. Gas is priced by flow, not by pressure, using hourly cost = flow in Nm3/h x unit price per Nm3. Typical flows on thick-section work are 2-6 Nm3/h for oxygen, 20-40 Nm3/h for nitrogen at 18-25 bar, and 15-30 Nm3/h for compressed air at 12-16 bar. That puts oxygen at roughly USD 1-3 per hour for 10-20 mm plate, nitrogen at USD 6-20 per hour depending on supply mode, and compressed air under USD 2 per hour in compressor power and maintenance. Supply mode matters more than the gas itself: a 40-litre nitrogen cylinder at 20 bar holds only about 7 Nm3, so it empties in 15-20 minutes and you need four bottles an hour, which is why liquid nitrogen in a dewar (500 litres, about 350-400 Nm3 usable) typically cuts the nitrogen cost by 60-75%. Compare the gas bill with the labour bill before deciding: one metre of oxygen-cut edge that has to be ground before welding costs more in wages than the nitrogen needed to cut it clean.
Can you weld or paint directly on an oxygen-cut laser edge?
No - the oxide layer has to come off first, and that is the hidden cost of oxygen cutting. Oxygen cutting leaves an iron oxide skin (typically 5-20 microns) plus a heat-tinted zone; it is friable, it is not electrically conductive in the same way as the base metal, and it traps moisture. For welding, clean back to bright metal at least 20-25 mm either side of the joint, which in practice means grinding or flap-discing 0.2-0.5 mm off the cut face, otherwise you get porosity, lack of fusion and spatter. For coating, an oxide edge is a classic disbond line: ISO 12944 coating systems assume a properly prepared substrate, and paint or powder applied straight over a laser-oxygen edge usually fails a cross-hatch or pull-off test at the edge. Nitrogen cutting avoids the whole step - the edge is oxide-free and needs only a solvent wipe. This is why the higher hourly nitrogen cost often disappears in the labour it saves: at USD 25-35 per hour of shop labour, grinding one metre of edge takes 0.5-1.5 minutes per side, and a six-metre beam has 12 metres of weld-relevant edge.
What gas pressure, purity and nozzle should I run for 12-25 mm H beam flanges?
For 12-25 mm carbon steel the two parameters that decide quality are oxygen purity and pressure stability, not peak pressure. Run at least 99.5% oxygen, and 99.7% for 20 mm and above; set the inlet at the machine around 0.8-1.0 MPa and regulate down to 0.06-0.10 MPa at the nozzle for 12-20 mm, rising to 0.10-0.15 MPa for 20-25 mm, with a 1.2-1.6 mm single or double nozzle. If the job needs a weld-ready edge and you switch to nitrogen, use 99.99% minimum (99.999% for stainless) at 15-20 bar for 12-16 mm and 20-25 bar for 20-25 mm with a 2.0-2.5 mm nozzle. Purity below 99.9% shows up immediately as a brown tint and bottom dross, because the residual oxygen is enough to oxidize the kerf. Measure purity and dew point at the torch end of the line, not at the tank - a 20 m hose run with a leaking fitting, a rubber hose that has absorbed moisture, or a regulator with a dirty seat will degrade gas that left the supplier perfectly clean. Pressure at the nozzle is what the cut actually sees, so fit a gauge at the machine inlet and log it once per shift.
Can a 20 kW fiber laser cut 20 mm carbon steel with compressed air?
It can pierce it, but it will not hold production quality, and on an H beam line quality is the whole point. Compressed air is 21% oxygen, so the cut is a partial oxidation process: above about 6-8 mm on carbon steel the bottom edge carries dross, the kerf loses squareness by 2-4 degrees, and the cut face takes an oxide/nitride tint that has to be removed before welding anyway. On 20 mm flange, air cutting is a trial-cut or rough-blanking option, not a production process - and if you have to grind the edge afterwards, you have paid the air cost and the labour cost. Air also brings its own hardware conditions: it must be dry and oil-free to ISO 8573-1 Class 1 for particles, water and oil (dew point around -40 degrees C), delivered at 12-16 bar with enough flow for the nozzle. Moisture and oil are what destroy protection lenses and nozzles, and a compressor sized for the average flow will starve the cut at the pierce, which is exactly where the dross starts. Use air where it belongs: thin brackets, jigs, temporary works and non-visible parts.
Why is my cut edge discoloured, drossy or rough - is it the gas or the parameters?
Work through five causes in this order, because that is roughly their real frequency: gas, nozzle, focus, speed, material. Gas first - check purity at the torch, check for a pressure drop during the cut (a gauge that sags when the pierce starts means the supply is undersized), check for condensation in the line on the first shift of the morning. Nozzle second - a worn or oval nozzle, or spatter on the face, changes the jet shape and produces a one-sided rough edge, so inspect under magnification and replace on a count, not on feel. Focus third - a dirty or burnt protection lens and a focus position that is a millimetre off both read as 'bad gas' to an operator. Speed fourth - too fast leaves hard, thin dross that chips off and a rounded top edge; too slow leaves soft, bubbly dross and a wide heat-affected zone. Material last - mill scale, rust and paint all change absorption, and a heavily scaled flange can cut perfectly on one face and badly on the other. Change one variable at a time and keep the nozzle, pressure and focus documented per thickness so the next operator starts from a known recipe instead of guessing.
How do you cut assist gas cost without giving up weld quality?
Run a hybrid strategy rather than picking one gas for the whole shop: default to oxygen for 8 mm and above on structural carbon steel that will be welded after normal edge prep, and reserve nitrogen for parts where the cut face is visible, is the weld preparation itself, or is stainless or galvanized. Then attack the real drivers. Match nozzle size and pressure to thickness - over-pressure wastes gas and over-cools the kerf, which produces dross that you then pay to remove. Cut fewer pierces: nesting parts to share common lines and starting from the plate edge on open contours can remove hundreds of pierces per beam, and each pierce burns 2-6 seconds of gas at full flow. Fix leaks in high-pressure lines, because nitrogen at 20 bar leaks silently and a 1 mm hole can waste 5-10% of your total flow. Move from cylinders to liquid supply once you cut nitrogen more than a few hours a day. And on thick plate, consider piercing with oxygen and switching to nitrogen only for the finished contour where the edge has to be clean - the pierce is where most of the gas and most of the dross risk sit.
Cylinders, bundles, dewars or an on-site nitrogen generator - which supply mode is right?
Size the supply from your hourly flow and your cutting hours, not from the invoice price. A 40-litre cylinder holds about 7 Nm3, so at 25 Nm3/h you are changing bottles every 17 minutes; a 12-16 bottle bundle buys you a few hours and a lot of handling; a 500-litre liquid dewar gives roughly 350-400 Nm3 usable, which is 12-16 hours of cutting and usually a week of single-shift work, at maybe a quarter of the cost per Nm3 of cylinders. An on-site PSA nitrogen generator at 99.9-99.99% with a buffer tank starts to pay above roughly 1500-2000 hours a year of nitrogen cutting - but validate purity and flow at full demand before you buy, because a generator that drops to 99.5% under peak load will give you tinted edges on stainless. For oxygen, a 40-litre cylinder holds about 7 Nm3 and lasts 2-3 hours at 2-4 Nm3/h, so a small liquid oxygen dewar with an evaporator is the cheaper route once you use more than a cylinder a day. Whichever mode you choose, put a regulator, filter and gauge at the machine, keep the high-pressure hose run short, and include the gas package in the machine quotation so the commissioning engineer can set the recipes against the gas you will actually run.
Technical Specifications of Intelligent H beam Laser Cutting Machine
| Parameter | Value |
|---|---|
| Share | |
| Categories | H Beam Cutting Machine |
| Brand | YOMI CNC Cutting&Welding Machinery |
| Product Specifications | YM-XHJG-1250 |
| Flange width | 100-600mm |
| Workpiece height | 100-1250mm |
| Cutting mode | Fiber laser |
| Cutting thickness | 1-30mm |
| Bevel angle | ±45° |
| Max weight | 6000kg |
| Cutting length accuracy | 0.05mm |
| Laser power | 20KW |
| Equipment size | 30m*10m*5m |
Product Gallery







Applications
The Intelligent H beam Laser Cutting Machine is widely applied in steel structure prefabricated buildings, bridge and infrastructure construction, shipbuilding and marine engineering, heavy machinery manufacturing, power plant and industrial facilities, and offshore wind power structures.
Learn more about the Intelligent H beam Laser Cutting Machine:
https://www.steelstructurer.com/pid18427150/Intelligent-H-beam-Laser-Cutting-Machine.htm
For more information about Intelligent H beam Laser Cutting Machine and other steel structure intelligent equipment, contact YOMI CNC Cutting & Welding Machinery. Our team of experts is ready to help you find the best solution for your manufacturing needs.

- Full Name:
- YOMI WhatsAPP
- Tel:
+86 19053498672
- Email:
- sales@yomi-china.com
- WhatsApp:
- 8619053498672
- Address:
- Factory Adress: 9 Changjie Road, Ningjin,Dezhou, P.R.China

